songpaste9

Peugeot 208 Key Replacement It is best to leave the replacement of Peugeot keys for 208 to auto locksmiths with the right equipment and expertise. They can create and program new keys quicker than a dealership and at a lesser cost. A dead battery for your coin is most likely to be at fault the reason your key-fob stops locking or unlocking doors. There are also other reasons why the key may be malfunctioning. Dead Coin Battery A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also preventing it from starting the engine. If this is the case, you'll need to apply the backup starting technique that is described in the owner's manual for your vehicle. Another reason the 208 won't start is because the spark plugs are been damaged. why not try this out are responsible to ignite the fuel that starts the engine. However they are limited in their time of life. If they aren't used enough and they fail, they'll eventually die. There is an easy solution to this issue. Check the voltage of your battery using a multimeter. If it is below 11.5 volts then you must replace it. If the battery has corrosion it is crucial to clean its contacts. This can be done by lifting the rubber covers covering the two battery terminals and using wire brushes to clean any corroded parts of the battery. It is then time to reconnect the cables that connect the positive and negative poles. Water Damage If your 208 won't start and the battery isn't running, then make sure whether the spark plugs are working. You may find that they are dirty and don't spark. This can be easily corrected by cleaning the spark plugs in the workshop. Peugeot cars are equipped with a key with a transponder compatible with the immobiliser. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged then it will not transmit the correct signal to the vehicle. This is a frequent issue that is caused by water damage. This is most common in colder climates where the vehicle may have been exposed to rain or snow. If this is the case, you should call a reputable auto locksmith who will have all the tools and equipment required to change the key's programming. They'll also have the latest technology and equipment needed to create the Peugeot smart key. The process shouldn't take more than 15 minutes. Faulty Battery Contacts Peugeot changed from the carbon-encased transponder chips to a brand new type of chip that uses electronic components in circuit boards. This new technology works great when it's brand new, but over time the circuit boards start to degrade and stop working properly. This can stop the immobiliser chip from activating, so your car won't start. If this is the case it's a good idea get in touch with a Peugeot specialist or locksmith. A common issue occurs when the battery of the key fob starts to die. This causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a new blade for you, it's typically a quick fix. Faulty Receiver Module If your Peugeot key fob has stopped working after dropping it on the ground, being exposed to a sudden rain or accidentally washing it, it could be due to a defective receiver module. The receiver is responsible for transmitting radio frequency signals to an on-board computer which controls the centralized locking system in your Peugeot vehicle. The key fob itself has rubber seals to prevent water from getting to the electronic chip inside. Water can damage the chip when it is exposed to the water for an extended period of period of. The high salt content of the ocean or pool could cause damage to the key fob, especially if it is submerged. The module will need to be replaced if the Peugeot spare key is no longer working. This is only done by an expert auto locksmith or Peugeot specialist. Peugeot keys unlike other automobiles, are secured by an immobilizer device. This requires the correct coding to start the car. This is the reason why you should only go with a knowledgeable Peugeot locksmith to handle the task of designing and programming the replacement. Computer on-board is not working properly The on-board computer of your Peugeot is responsible for various functions in your car including airbags and power windows. If something goes wrong with these systems, it will typically show a code that identifies the issue. The code will be stored in the system until the issue is fixed. This could mean that the on-board computers to be replaced. One of the most frequent reasons for the airbag light turning on is loose or corroded connections within the airbag sensor. This can be caused by wear and tear, aging or exposure to salt and moisture. This problem should be taken care of as soon as you can, as an airbag malfunctioning could pose a risk in the event of an accident. If your Peugeot is showing a card not detected error, then the battery in the key fob might be weak or dead. This will stop the key fob sending a signal to disarm the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob, then trying to start your car. If this does not work then the battery in the key fob is in need of replacement.